SKU: FBK 12000 BUS Categories: ,

Firat FBK 12 000 BUS Spraybooth 48000 M3H


Product Description: 

A Painting and Drying Spraybooth is the structure where a vehicle is painted with a spray gun. It has a low-pressure air channel where the air is removed from the facility through a filtering system.

Paint stop filters remove various dust and particles from the air. The spray booth unit is equipped with fan-motor units that can be installed on the facility floor, with an entrance ramp at the front and a metal basement to connect to the air circulation units.


The auto painting and drying operation follows strict health and safety guidelines. It conforms to TSEK which is determined by the Quality conformity certificate no. 35 -14.02/1557 of 2001. Under Law no. 132 and TSE legislation, the “Production Compliance Certificate” has been approved. Analysis conducted by TUBITAK ENERGY SYSTEMS and ENVIRONMENT RESEARCH INSTITUTE ENVIRONMENT DIVISION, stated in report no. B.02.1BAK. and Project no. 51H2402, that FIRAT Auto Painting Spray Booths do not constitute any environmental pollution.

  • Images are for illustration purposes only 
  • All preparation bays, mixing rooms, and spray booths can be customised according to your requirements.

Please contact us for more information.  

Technical Specifications

Internal Dimensions 12.000(L) X 5000(W) 4970(H) mm 
External Dimensions 12.200(L) X 5100(W) X 5600(H) mm 
(Units are excluded) 
Entrance Door 3800 (W) x 4200 (H) mm 
Quantity of Entrance door leaf 4 PCS 
Service Door 800 (W) x 2192 (H) mm x 2 Pieces 
 Top Lighting 64X36W 
Lower Lighting 48X18W 
 Fan Motors 2 x 10 HP (7,5 KW) 
Fresh Air Air Flow 48.000 m³/h – ILKE Fan 
Burner 2 x 250.000 Kcal/h – Diesel burner -Riello 
Exchanger 2200 mm single layer 
 Max.Drying 60⁰C / 80⁰C 
Exhaust Fan Motors 2 x 10 HP (7,5 KW) 
Unit Air Flow 48.000 m³/h – ILKE Fan 
Floor Filter EU3 
Ceiling Filter EU5 
Grates  1 Line Grates -5 mm thickness (Concrete Excavation project will be made.) 
Max.Weight Without Metal Basement (With Tunnel) 
Metal Basement NO 
Plenum  600mm 
Max.Electric Power 45 KW 
Panel Power 380 volt 
Electric Command 24 volt 
Chimneys  Belong to the customer!!! 

Main Cabin

The side walls are made of 1 mm thick galvanized sheet metal, with 60 mm glass wool insulation. The outside surface of the panels are powder coated to provide an ergonomic view and longer life.

It has an illumination system which has been designed to optimise colour control during the painting phase.

The spray booth has a hanger system with rails hung up to the ceiling, which enables the painting of individual parts.

The ceiling section provides a homogeneous flow of air coming from the heat exchanger, through the plenum and filters.

The ceiling consists of sheet panels with special insulation support and to clean the air supplied to the booth, filter items made of non-flammable material, special high performance, long life is placed under the ceiling.

There are 3 doors in the front and back of the booth and a 1 door system for personnel entry and exit. Doors have observation windows made of safety glass. The thickness of the doors is 60 mm and insulated with 60 mm glass wool. All Windows include glass.

Air Make-Up Unit

This unit supplies fresh filtered air into the booth and extracts the used air outside during the painting. During the drying phase, the unit heats the air to 60 °C and supplies it into the booth. This mixes used air with fresh air through the multi dampe and circulates it after reheating.

A diesel burner with a capacity of 250.000 kcal/h heats the air and features an exchanger made of 304 quality stainless steel sheets. Start-up takes approximately 15 minutes to increase air temperature up to 60 °C, depending on ambient temperature.

Circulation of the heated or non heated air into the booth is provided by two industrial fans, each with a capacity of 48.000 m³ / h. The air is delivered to the booth through a pre-filter while output air is controlled by a damper in the output air channel.

Electrical System

Electric and Command Panel

The electrical command panel houses the motors and devices in an enclosure where they can be operated and controlled from a central point.

The Galvanized sheet panels and steel profiles are resistant to bumps, completely covered, waterproof and damp-proof.

The panel includes all switches and fuses necessary for motors and electrical devices, signal lamps, thermal relays and contactors.


The electrical panels and devices are protected by heatproof cables. Electric lines are placed on a base so that replacement is easy.

Ready to operate devices: 380 V.50 Hz. The voltage of control devices are 24 volts.